
LBI-38421A
8
There are five (5) different optional interchangeable
control panels available for selecting a two-channel radio, an
eight (8) or sixteen (16) channel radio. The five control
panels are as follows:
•
Option MK1J: Two (2) Channel without Scan
(19A705800P100)
•
Option MK1L: Eight (8) Channel without Scan
(19A705800P101)
•
Option MK1N Eight (8) Channel with Scan
(19A705800P102)
•
Option MK1P: Sixteen (16) Channel without Scan
(19A705800P103)
•
Option MK1R: Sixteen (16) Channel with Scan
(19A705800P104)
CAUTION
Optional Control Panels 19A705800P100
thru P104 are for use in MLS radios
19A705800P1 thru P7 ONLY. They are
NOT compatible with the 19A704991( )
series MLS radios. MLS radios
19A704991P1 thru P7 use Control Panels
19A704991P101 thru 19A70499lP104
ONLY.
MICROPHONE
The mobile radio uses a dynamic microphone with a
built-in transistorized pre-amplifier. The microphone is
housed in a sturdy case and the extendable coiled cord plugs
into a jack provided at the back of the radio. The
microphone is secured to the radio by means of a strain
relief hook on the microphone cable.
HOOKSWITCH
A hookswitch is provided with the radio to hold the
microphone. Removing the microphone from the hookswitch
disables the Channel Guard, enabling the operator to
monitor the channel before sending a message. Removing
the microphone while in the SCAN mode, will also disable
SCAN until the microphone is placed back into the
hookswitch.
CHANNEL GUARD
Channel Guard provides a means of restricting calls to
specific radios through the use of a continuous tone or
digitally coded squelch system (CTCSS or DCG). Tone
frequencies range from 67.0 Hz to 210.7 Hz. 33 standard
tones and 104 unique digital codes are available.
CARRIER CONTROL TIMER
The Carrier Control Timer turns off the transmitter after
the microphone push-to-talk switch has been keyed for a
pre-programmed time period. The timer can be
programmed to time out and sound an alert tone in 30-
second increments up to 7.5 minutes.
EXTERNAL SPEAKER (OPTIONAL)
An optional 4-Watt, 4-ohm external speaker is available
for use with the radio. The speaker is supplied with a
mounting bracket and mounting hardware. The speaker
leads connect through connector J701 on the back of the
radio (refer to applicable Installation Manual).
PROGRAMMING
The EEPROM allows the radio to be programmed or
reprogrammed as needed to adapt to changing system
requirements. RF frequencies, Channel Guard tones, digital
codes, and CCT can be reprogrammed. The EEPROM is
programmed through the radio MIC connector (J701) using
an IBM compatible PC and special cable. Programming
instructions are provided in the respective programming
manual.
OPERATION
This section provides a description of the Control and
Indicator functions as well as the basic procedures for
transmitting and receiving messages. Complete operating
instructions for the radio are provided in the respective
Operator’s Manual.
CONTROLS
The radio control panel contains the VOLUME control,
the POWER on/off switch, the MONITOR switch and the
CHANNEL select switch. The switch functions are as
follows:
POWER
A momentary type switch to turn the
radio on or off. Press once to turn the
radio on; press again to turn the radio
off. Power ON is indicated by an
illuminated channel number on the
system module.
VOLUME
Two momentary type switches to adjust
the volume. Press and hold the MAX (up
arrow) to increase the volume. Press and
hold the MIN (down arrow) to decrease
the volume.
MONITOR
A momentary type switch to allow you to
monitor the selected channel before
transmitting a message. It disables
Channel Guard and squelch and will
allow you to hear noise if the channel is
not busy. This may be convenient when
setting the volume to the desired
listening level.
Comentarios a estos manuales